P-80 Grip-It

: $5.00
$4.50

Temporary gauntlet lubricant – safe and ready to use – helps ease the installation of your gauntlet! Will not leave any residue on your firearm if the gauntlet is removed.

In stock

Part #: 10190 Category:

Installation:

It is best to begin in a clean and well-lighted workspace. By following these few simple steps you will ensure the best possible installation of your new EZR grip.

You will need a hairdryer to warm the grip prior to installation. It is a good idea to choose a warm room for the process so the EZR grip will stay flexible throughout the installation. If lubrication is needed EZR approved P-80 Grip-It may be used. (see our product listing.)

IMPORTANT:  Make sure any firearm to be handled is unloaded and mounting surface is clean and free of any grit or debris

If you are mounting an EZR Gauntlet to an AR pistol grip, after following step 1, remove the pistol grip from the AR prior to installation

  1. Inspect the EZR grip interior socket, making sure it is clean and clear of any grit or debris.
  2. Warm the EZR grip with a hair dryer until flexible.   Note: DO NOT overheat grip and DO NOT use a heat gun
  3. If lubricant is to be used, apply a thin, even film of P-80 Grip-It to the surface where the EZR grip will be mounted. Note: If this is a firearm you rely upon for daily use, be aware that the use of lubricant for installation requires the grip be allowed to set for 24 hours before being put into service.
  4. Take the warmed grip and gently stretch the opening a few times before attempting to install. Make sure you do not have excess lubricant on your hands, which could cause them to slip
  5. Stretch-open the grip and ease it over the butt of the handgun, or the AR pistol grip. Once in place, you will find that a lubricated installation allows you to slide the grip over the surface until it is right where you want it. Grip it in your hand and make sure the position is just right
  6. Allow the firearm or AR pistol grip to set undisturbed for 24 hours to ensure a snug, clinging attachment of the EZR grip.

Reviews

There are no reviews yet.

Be the first to review “P-80 Grip-It”

P-80 Grip-It

: $5.00
$4.50

Temporary gauntlet lubricant – safe and ready to use – helps ease the installation of your gauntlet! Will not leave any residue on your firearm if the gauntlet is removed.

In stock

Part #: 10190 Category:

Installation:

It is best to begin in a clean and well-lighted workspace. By following these few simple steps you will ensure the best possible installation of your new EZR grip.

You will need a hairdryer to warm the grip prior to installation. It is a good idea to choose a warm room for the process so the EZR grip will stay flexible throughout the installation. If lubrication is needed EZR approved P-80 Grip-It may be used. (see our product listing.)

IMPORTANT:  Make sure any firearm to be handled is unloaded and mounting surface is clean and free of any grit or debris

If you are mounting an EZR Gauntlet to an AR pistol grip, after following step 1, remove the pistol grip from the AR prior to installation

  1. Inspect the EZR grip interior socket, making sure it is clean and clear of any grit or debris.
  2. Warm the EZR grip with a hair dryer until flexible.   Note: DO NOT overheat grip and DO NOT use a heat gun
  3. If lubricant is to be used, apply a thin, even film of P-80 Grip-It to the surface where the EZR grip will be mounted. Note: If this is a firearm you rely upon for daily use, be aware that the use of lubricant for installation requires the grip be allowed to set for 24 hours before being put into service.
  4. Take the warmed grip and gently stretch the opening a few times before attempting to install. Make sure you do not have excess lubricant on your hands, which could cause them to slip
  5. Stretch-open the grip and ease it over the butt of the handgun, or the AR pistol grip. Once in place, you will find that a lubricated installation allows you to slide the grip over the surface until it is right where you want it. Grip it in your hand and make sure the position is just right
  6. Allow the firearm or AR pistol grip to set undisturbed for 24 hours to ensure a snug, clinging attachment of the EZR grip.

Reviews

There are no reviews yet.

Be the first to review “P-80 Grip-It”

FREE SHIPPING on 5+ Grips!

FREE shipping on 5+ Grips!

# of Grips Shipping
1 & 2
$10.40
3 & 4
$16.10
5+
FREE
No international orders. We ship within the US only. More information is available on the Policies & Procedures page.

The EZR Warranty

EZR Sport gun grips will not tear or rip during installation. Nor will they rotate or move after extended use.

EZR Sport guarantees these products to be free of defects in original workmanship and materials. If any defect develops, we will replace the product at no charge, provided the defect is not the result of mishandling or abuse on the part of the user, and that the defective product is returned to the factory with transportation charges prepaid.

EZR Gun Grips are unmatched for quality, durability, and molding flexibility.

EZR gun grip gauntlets are manufactured through a patented proprietary process using our unique EZR Foam. Made from a unique phthalate-free PVC vinyl closed-cell foam of unequaled durability and comfort, EZR Foam offers a smooth velvet surface that is non-slip under adverse conditions and improves with use. 

EZR Foam is a high-density shock absorber and insulator with unequaled abrasion resistance. It is non-absorbant; dirt and oils can be easily washed away. Plus, EZR Foam is impervious to UV degradation and chemicals such as DEET in comparison to EPDM rubber, a material commonly used in rubber grip sleeves.

Other items you may like

This site uses cookies to offer you a better browsing experience. By browsing this website, you agree to our use of cookies.